Jump to content

I need your help with Vision in Labview


Recommended Posts

I use the Vision Builder and convert to Labview file for use with control

the

servo motor. But I have some problem as shown below

1.When I finish the programm with Vision Builder I convert to Labview file

,in this state I don't found the problem

2.I cannot run Labview file because it has some problem about there are

not found some of the command such as "IMAQ create" in the Block diagram and

it is shown the "?" in the block ,then I don't sure that I'm install the programm

right?

3.When I open Labview file again It was asked for "IMAQ image.ctl" and any

of

the file with type ".ctl,.ctt" I don't know where can I find?

4.When I use Labview to manage with the Image I input the command "IMAQ

Build

Coordsys" then the programm asked for many of the "IMAQ image.ctl" too.

5.My device is :

- Camera:Busler scA640-70fm

- NI pci 6221

- NI pci 8254r

My programm is:

Labview 8.5

Vision Builder AI 3.0.1

Vision assistant 8.0

Vision aquisition 8.2.2

What Can I manage my problem?

I'm really need your help

Help me please!!!

Link to comment

I use the Vision Builder and convert to Labview file for use with control

the

servo motor. But I have some problem as shown below

1.When I finish the programm with Vision Builder I convert to Labview file

,in this state I don't found the problem

2.I cannot run Labview file because it has some problem about there are

not found some of the command such as "IMAQ create" in the Block diagram and

it is shown the "?" in the block ,then I don't sure that I'm install the programm

right?

3.When I open Labview file again It was asked for "IMAQ image.ctl" and any

of

the file with type ".ctl,.ctt" I don't know where can I find?

4.When I use Labview to manage with the Image I input the command "IMAQ

Build

Coordsys" then the programm asked for many of the "IMAQ image.ctl" too.

5.My device is :

- Camera:Busler scA640-70fm

- NI pci 6221

- NI pci 8254r

My programm is:

Labview 8.5

Vision Builder AI 3.0.1

Vision assistant 8.0

Vision aquisition 8.2.2

What Can I manage my problem?

I'm really need your help

Help me please!!!

Link to comment

QUOTE (Poom-Thailand @ Jan 16 2009, 11:49 AM)

I use the Vision Builder and convert to Labview file for use with control

the

servo motor. But I have some problem as shown below

1.When I finish the programm with Vision Builder I convert to Labview file

,in this state I don't found the problem

2.I cannot run Labview file because it has some problem about there are

not found some of the command such as "IMAQ create" in the Block diagram and

it is shown the "?" in the block ,then I don't sure that I'm install the programm

right?

3.When I open Labview file again It was asked for "IMAQ image.ctl" and any

of

the file with type ".ctl,.ctt" I don't know where can I find?

4.When I use Labview to manage with the Image I input the command "IMAQ

Build

Coordsys" then the programm asked for many of the "IMAQ image.ctl" too.

5.My device is :

- Camera:Busler scA640-70fm

- NI pci 6221

- NI pci 8254r

My programm is:

Labview 8.5

Vision Builder AI 3.0.1

Vision assistant 8.0

Vision aquisition 8.2.2

What Can I manage my problem?

I'm really need your help

Help me please!!!

Hi,

The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl

The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create

Hope this helps.

Link to comment

QUOTE (Poom-Thailand @ Jan 16 2009, 11:49 AM)

I use the Vision Builder and convert to Labview file for use with control

the

servo motor. But I have some problem as shown below

1.When I finish the programm with Vision Builder I convert to Labview file

,in this state I don't found the problem

2.I cannot run Labview file because it has some problem about there are

not found some of the command such as "IMAQ create" in the Block diagram and

it is shown the "?" in the block ,then I don't sure that I'm install the programm

right?

3.When I open Labview file again It was asked for "IMAQ image.ctl" and any

of

the file with type ".ctl,.ctt" I don't know where can I find?

4.When I use Labview to manage with the Image I input the command "IMAQ

Build

Coordsys" then the programm asked for many of the "IMAQ image.ctl" too.

5.My device is :

- Camera:Busler scA640-70fm

- NI pci 6221

- NI pci 8254r

My programm is:

Labview 8.5

Vision Builder AI 3.0.1

Vision assistant 8.0

Vision aquisition 8.2.2

What Can I manage my problem?

I'm really need your help

Help me please!!!

Hi,

The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl

The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create

Hope this helps.

Link to comment

QUOTE (Antoine Châlons @ Jan 16 2009, 06:04 PM)

Hi,

The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl

The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create

Hope this helps.

I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program?

Link to comment

QUOTE (Antoine Châlons @ Jan 16 2009, 06:04 PM)

Hi,

The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl

The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create

Hope this helps.

I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program?

Link to comment

QUOTE (Poom-Thailand @ Jan 17 2009, 05:05 AM)

I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program?

If you have installed the Vision Development Toolkit from the LabVIEW DVD go into Add/Remove Programs Control Panel and do a repair of your install. If you haven't yet done so then install that package.

Rolf Kalbermatter

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.