kmc

thanks ton for your reply omar, can you send me the labview file which u had done ??? the one which had the sequence wait ??? regards Ashwin QUOTE (Omar Mussa @ Nov 3 2008, 08:29 AM)

I AM SORRY I DINT MEAN TO ASK YOU FOR A FULL SOLUTION CENTER I Would like to explain what i have done first so that It would be easier for you to help me... 1. As you see there are 6 STATIONS.Each Stations perform various Tasks.Basically THE MAIN IDEA is to MONITOR THESE STATIONS. THERE ARE STEPS TO MONITOR STATIONS 1.AT FIRST WHEN OPERATOR LOADS THE PART THE PBX(switch) WILL GET ENERGIZED. 2.10 MINUTE TIMER IS SWITCHED ON AT THIS STAGE.AT 9TH MINUTE THE TIMER STARTS FLASHING (THAT INDICATES THE OPERATOR SHOULD BE AT THE STATION) 3.IF THE OPERATOR IS NOT THERE AT 10 TH MINUTE U GET AS FAIL(THE PART SHOULD BE SET ASIDE FOR 1 HR TO COOL)...THATS THE REASON WHY THE FLASHING PART HAS BEEN KEPT 4.THERE IS A BALL KEPT ON THE PART...AS SOON AS THE BALL IS KEPT...ANOTHER 5 MINUTE TIMER IS SWITCHED ON...AT THAT TIME THE OPERATOR WILL NOTE DOWN FEW VALUES 5.AT 5TH MINUTE ADJUST TO MAX VALUE,OPERATOR REMOVES PART AND RESET THE TIMER AND TURN OFF THE SWITCH IF YOU SEE WHAT I HAVE DONE IN TIMER U SEE THAT 0-20-40-60-80-100(THE ONE JUST ABOVE READY) THAT IS A INDICATION 0-80---GREEN 80-90---YELLOW AT 90---FLASHING RED...I HAVE WORKED ON FLASHING RED... FEW FOLKS HAD TOLD ME TO USE A JKI SYSTEM...I AM TRYING TO READ THAT AS OF NOW...I WOULD REALLY APPRECIATE IF YOU COULD HELP ME IN THIS... I AM PUTTING MY BEST EFFORT AS OF NOW... I HAVE BEEN BREAKING MY HEAD FOR A REASON... :headbang: I AM EXTREMELY SORRY FOLKS... I HOPE TO HEAR FROM YOU SOON... REGARDS ASHWIN.... QUOTE (Ton @ Nov 12 2008, 09:00 PM)

yes its going to be a tough ask for me.... anyways guys a request those who have time...pls help me....i m a fresher in labview...this wouldnt be difficult for you guys... folks...who can help me with this....i would be really greatfull...its just a request...since i am running out of time i m forced to ask u.... hope u understand my situation.. regards Ashwin QUOTE (jcarmody @ Nov 12 2008, 06:45 PM)

Thanks a lot omar and Jim ….i really appreciate you guys for patiently replying to my questions… Hats off to you…Was down with flu…so I wasn't able to check this response for 2 weeks…since I was down At first…Jim can you resend me the sequencer file…it is asking for "parse state queue_jkl_lib_state _machine.vi file " I am not sure of what it is.. As far as this program is concerned…there is no question of ELAPSE TIME..In 10 minutes if the operator is not in front of the system...the program needs to stop. the operator needs to set aside the component for an hour to cool down...before starting the program so basically in idle state the timer runs and flashes in 9 minutes.... Omar, Can you send me the document you had done…it would be really great..since I am running out of time..i just started this…I wasn't able to do anything for the past 2 weeks since I was done with flu I really don't have enough time to think.. Folks…..pls help me… Hope I am not bothering you…I m in a precarious situation. i would like to thank you guys for viewing my work... thanks a lot.... regards Ashwin QUOTE (Omar Mussa @ Nov 3 2008, 08:29 AM)

QUOTE (Michael_Aivaliotis @ Oct 31 2008, 08:34 AM) really sad to see 144 views and none of them replying... anyway thanks for viewing guys... regards Ashwin

HI hope you remember me...i had spoken to you couple of months back...i have few questions regarding my new independent research in school...thought u could help me with it....i tried working on it...and they have asked me to submit this in a week s time so that i would be able to write a report on it. this is how it goes basically there are 6 stations each stations perform operations based on a particular time period.For eg. in the research given to me there are 6 stations and there are 3 balls which need to be used while operating the stations.basically what they wanted me to do is these steps 1.after the operator loads the part and prsses pbx(switch) the operation should start 2.the the inductor should energize the capacitor to start at proper time and begin the timer operation for 10 mins,for zero calibration(zero max and zero min in front panel) when the 10 min timer is running the flash light should work indicating the operator to be at the corresponding station..the operator will adjust the circuit until the 10th minute if the operator doesnt finish at the 10th minute.Consider the component as fail wait for 1 minute before the next start is clicked 3.keep the ball in the circuit and start 5 minute timer. 4.At 5th minute adjust to maximum value(span max and span min in front panel) and reset the timers and turn of crx. i have drawn the front panel and showed the flashing part basically 0-80% it should be green 80-90% yellow 90-100-flash red It would be of great help if you could help me out in doing this. HOPE NORM KIRCHNER CAN HELP ME OUT. I HAVE ATTACHED THE FRONT PANEL AND BACK END FOR THIS PROGRAM..............THIS IS MY INDEPENDENT RESEARCH WORK IN SCHOOL..I NEED TO SUBMIT THIS IN A WEEK...

PLEASE HELP ME OUT THIS...IF I AM NOT CLEAR ENOUGH PLEASE TELL ME..THIS WILL HELP ME WITH MY RESEARCH WORK... THIS IS A REQUEST...HOPE THESE THINGS ARE VERY SIMPLE FOR YOU...Since I AM A BEGINNER FINDING IT TOUGH..HOPE YOU GUYS UNDERSTAND MY PROBLEM

HI hope you remember me...i had spoken to you couple of months back...i have few questions regarding my new independent research in school...thought u could help me with it....i tried working on it...and they have asked me to submit this in a week s time so that i would be able to write a report on it. this is how it goes basically there are 6 stations each stations perform operations based on a particular time period.For eg. in the research given to me there are 6 stations and there are 3 balls which need to be used while operating the stations.basically what they wanted me to do is these steps 1.after the operator loads the part and prsses pbx(switch) the operation should start 2.the the inductor should energize the capacitor to start at proper time and begin the timer operation for 10 mins,for zero calibration(zero max and zero min in front panel) when the 10 min timer is running the flash light should work indicating the operator to be at the corresponding station..the operator will adjust the circuit until the 10th minute if the operator doesnt finish at the 10th minute.Consider the component as fail wait for 1 minute before the next start is clicked 3.keep the ball in the circuit and start 5 minute timer. 4.At 5th minute adjust to maximum value(span max and span min in front panel) and reset the timers and turn of crx. i have drawn the front panel and showed the flashing part basically 0-80% it should be green 80-90% yellow 90-100-flash red It would be of great help if you could help me out in doing this. HOPE NORM KIRCHNER CAN HELP ME OUT. I HAVE ATTACHED THE FRONT PANEL AND BACK END FOR THIS PROGRAM..............THIS IS MY INDEPENDENT RESEARCH WORK IN SCHOOL..I NEED TO SUBMIT THIS IN A WEEK... PLEASE HELP ME OUT..! View Member Profile View Member Albums Remove Friend Send Message Find Member's Topics Find Member's Posts ipsmenu.register( "post-member-48640", '', 'popmenubutton-new', 'popmenubutton-new-out' );

QUOTE (Norm Kirchner @ Jul 17 2008, 10:43 PM) Hey Norman,thanks a lot for replying to my msg.I had sent you the structure which i would like to have. basically what they were asking me is this 1.the program which was implemented was using a string array,they wanted me to convert to numeric array where the numeric array displays 0,1,2 if 0 is displayed------------it is a system colour 1 is displayed---it is red....it is fail 2 is displayed it is green.....it is pass at present the pass fail is displayed.. if we convert to numeric array instead of pass and fail it displays Numeric as 0,1,2....accordingly. how should i modify to get this result if 0 is displayed------------it is a system colour 1 is displayed---it is red....it is fail 2 is displayed it is green.....it is pass I am attaching the flow of program for better understanding. i am extremly sorry norman...i think i am bothering you a lot....it would be of great help if you could do this for me.. regards kmc QUOTE (Ton @ Jul 17 2008, 08:40 PM) Ashwin, check your keyboard, one of you shift-keys is stuck. Here's a generic solution. You could put this inside a sub-vi and use for several tables. Some tips: Don't use stacked sequences, they will bite you (I am aware this is a 'demo' VI). Ton Thanks a lot ton...! i am still trying...with a few things..i appreciate your help...!!! thanks kmc

QUOTE (Norm Kirchner @ Jul 17 2008, 05:28 PM) Thanks a lot Norman.I appreciate this........! as far this was my research work which my professor had asked me to do... as far this program is concerned she expects me to do few things 1.this array is a text array..i.e Pass and Fail..what she wants me to do is to convert this text array into a numeric array and she wants me to display the colour out here for eg. 0-system colour 1-Flashing red 2- Green I havent worked on this before i am a beginner in labview.so trying to learn lot of things nw it would be really great if you could help me out with this.Can you send me what you had tried as an attachment. thanks a lot for patiently answering my questions regards kmc QUOTE (kmc @ Jul 17 2008, 07:28 PM) Thanks a lot Norman.I appreciate this........! as far this was my research work which my professor had asked me to do... as far this program is concerned she expects me to do few things 1.this array is a text array..i.e Pass and Fail..what she wants me to do is to convert this text array into a numeric array and she wants me to display the colour out here for eg. 0-system colour 1-Flashing red 2- Green I havent worked on this before i am a beginner in labview.so trying to learn lot of things nw it would be really great if you could help me out with this.Can you send me what you had tried as an attachment. thanks a lot for patiently answering my questions regards kmc NORMAN,I HAVE ATTACHED FEW THINGS ALONG WITH THIS..I HAVE DONE FEW THINGS RANDOMLY...AS I TOLD THE TEXT ARRAY IS CONVERTED TO NUMERIC ARRAY AND DO I NEED TO CHANGE TABLE1 AND TABLE2 ACCORDINGLY.HAD STARTED WITH IT. I THINK YOU WOULD BE EASILY ABLE TO FINISH IT.COULD YOU PLEASE CHECK THIS..? THANKS ASHWIN

QUOTE (Gary Rubin @ Jul 17 2008, 03:45 PM) I SINCERLY APOLOGISE TO EVERY ONE.I SHOULDNT HAVE DONE THIS.........I AM REALLY SORRY FOR SPEAKING LIKE THAT. QUOTE (Phillip Brooks @ Jul 17 2008, 03:28 PM) All caps is considered a form of shouting. Shouting doesn't inspire people to get involved. You have only waited one hour. There are currently 9280 members and also non-members. 70 reads is not a lot... Thanks for becoming a Premium Member, but this is not a service. Your membership supports the operation of the forums, but the contributors are all volunteers; we share our knowledge for free. I don't have LabVIEW 8.5 ( I'm using very old 7.0) or I would look at your code and try to help. Give it a little time and someone should help... i AM SORRY FOR SPEAKING LIKE THAT.This is the first time i am into lava.i really dont have any idea how it goes.I understand it is an obligation.i had posted a request a month back this is the link http://forums.lavag.org/help-needed-with-labview-t11141.html though i worked on it and got the result that i wanted.you could see that there are more than 375 views but none have replied.I thought they were just viewing the file and not replying. i accept it was my mistake.I deeply regret for speaking like that. thanks Ashwin

QUOTE (kmc @ Jul 17 2008, 02:03 PM) I SEE MORE THAN 70 VIEWS WHY ISNT ANY ONE REPLYING....?? I THINK I HAVE WASTED TIME BY JOINING HERE...NO BODY REPLIES...!

QUOTE (normandinf @ Jul 17 2008, 01:37 PM) Can you look at the file which i had attached along with this.I HAVE USED THE ACTIVE CELL PROPERTY AND CELL BACK GROUND COLOUR PROPERTY.PLEASE HAVE ALOOK AT THE ATTACHED FILE. THANKS kmc

HI, I am creating a table.I am taking the contents of table1,table 2,table 3 in an array.While displaying the result,The contents of the table (i.e)the way it looks will change. i.e if i keep 0=system colour(i.e header in the table) as grey 1=red 2=green i am attaching the program along with this...pls try to help me out with this in short pass should be in green fail in red header in table grey. pls help me out with this