Jump to content


  • Posts

  • Joined

  • Last visited

1 Follower

LabVIEW Information

  • Version
    LabVIEW 2018
  • Since

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Ratataplam's Achievements


Newbie (1/14)



  1. Hi all, yes. I've implemented a APIs, LV queue based, to Tx\Rx message.
  2. Hi all, I'm moving the first steps in TS world and I try to communicate with a VI runs in asynchronous mode. First of all seem that I able to stop the VI at end of sequence, but I cannot read\write data from TS. To make simple the problem, I fixed a constant in my VI and connected it to indicator, mapping the indicator on TS parameter. In the TS sequence I check the value of TS parameter, but the result is different from the expected. Where is my mistake? Thanks for any suggestions p.s. LV2018 and TS2017SP1 was used to generate the problem 😃 asynch2.vi TestAsynch2_a.seq
  3. Hi, thanks for the support. The first attempts were done with embedded keyboard (I' use a laptop) and today with external usb keyboard, but the result is the same. :(
  4. Hi all I need to test my LV RT update without real target (cRIO-9045) and I don't need to use the real I/O module and real FPGA, I want to test only the interface betwwen host application (on PC) and RT application (cRIO). To do that I've used 1) "ni-linux-rt-pxi-system-image-2019.09_19.5_online_repack2.exe" to download the iso file : standard_x64_recovery.iso (84 MB) 2) After I 've Created a VM with Oracle VM 6.1 + “Oracle_VM_VirtualBox_Extension_Pack-6.1.12.vbox-extpack” Below the VM settings : a) Linux Ubuntu 64bit and 2GB RAM b) 10 GB c) EFI selected d) USB 3 controller for keyboard e) selected the *.iso file 3) after run ("avvia") and with keyboard arrow select "verbose mode" (keep in mind, the keyboards now works) but when the installation arrives at the first choice option I'm not able to select anything because the keyboards on VM doesn't work Any suggestion? Thanks
  5. Hi all, I'm a beginner with VS (Veristand), stimuls profile and real time seq. I nedd to introduce in my test a ramp, I found a ramp under Real-Time Sequence Library->Waveforms folder. The function required : RampOut—The variable to ramp from the InitialValue to the FinalValue. InitialValue—The starting value from which to start ramping. FinalValue—The ending value. Duration—The duration in seconds over which to ramp RampOut. My RampOut parameters (Temp2) is a I32 and the ramp accept only double, so the editor generate an error : "The expression Temp2 in of type int32 but is passed a reference into a reference parameter of type Double in Ramp(Tem2,0,100,20). Reference parameters must match exactly" How can 'cast' Temp2 in ramp function? Thanks
  6. Thanks at all, both solution works. My question is an academic question. If I connect the sine wave generator to AO port or to Multiply operator a "cast" (red dot) is used by LV. Now, I must certificated my project and the assessor could be ask something about the red dot so how I can demonstrate that I don't not loss the information ? One solution is the test as decribed by "infinitenothing" or logical approach as suggest by Jordan. Does exist the way to avoid the cast without change the HW settings? Regards
  7. Hi all, i try to generate a sinewave in FPGA (NI cRIO Platform), to do that I use the specific VI (Sine Wave Generator) for fpga to produce a sinewave in UINT16 data type. Unfortunatelly my AO module works with FXP data type (see attach) and I need to adaptd the UINT16 to AO module. A simple cast is not sufficent because I loss information, any suggestion ?
  8. Hi, simple the cRIO is already present in the lab :D
  9. thanks a lot, your suggestions have avoid several attempt
  10. Hi all, I need your opinion about a problem. I need to reproduce a data file on a cRIO. Typically the file is made of recorded data from the field with at least 2 columns : time and value. I would use a cRIO to reproduce the file and stimulate my target (device under test) with the same condition of the equipment on the filed. The idea is : 1) trasfer the file on cRIO file system and open it. 2) read the data from the file with Read Delimited Spreadsheet and save the value in an array 3) read the array, row-by-row, with an auto-indexed tunel loop 4) Inside the loop send the data, organized into a cluster, to cRIO FPGA via RT-FIFO 5) On FPGA keep in listen on the RT-read and get the message when ready Someone has experience in this case? Any suggestion? Thanks
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.