Poom-Thailand Posted January 17, 2009 Author Report Share Posted January 17, 2009 I use the Vision Builder and convert to Labview file for use with control the servo motor. But I have some problem as shown below 1.When I finish the programm with Vision Builder I convert to Labview file ,in this state I don't found the problem 2.I cannot run Labview file because it has some problem about there are not found some of the command such as "IMAQ create" in the Block diagram and it is shown the "?" in the block ,then I don't sure that I'm install the programm right? 3.When I open Labview file again It was asked for "IMAQ image.ctl" and any of the file with type ".ctl,.ctt" I don't know where can I find? 4.When I use Labview to manage with the Image I input the command "IMAQ Build Coordsys" then the programm asked for many of the "IMAQ image.ctl" too. 5.My device is : - Camera:Busler scA640-70fm - NI pci 6221 - NI pci 8254r My programm is: Labview 8.5 Vision Builder AI 3.0.1 Vision assistant 8.0 Vision aquisition 8.2.2 What Can I manage my problem? I'm really need your help Help me please!!! Quote Link to comment
Poom-Thailand Posted January 17, 2009 Report Share Posted January 17, 2009 I use the Vision Builder and convert to Labview file for use with control the servo motor. But I have some problem as shown below 1.When I finish the programm with Vision Builder I convert to Labview file ,in this state I don't found the problem 2.I cannot run Labview file because it has some problem about there are not found some of the command such as "IMAQ create" in the Block diagram and it is shown the "?" in the block ,then I don't sure that I'm install the programm right? 3.When I open Labview file again It was asked for "IMAQ image.ctl" and any of the file with type ".ctl,.ctt" I don't know where can I find? 4.When I use Labview to manage with the Image I input the command "IMAQ Build Coordsys" then the programm asked for many of the "IMAQ image.ctl" too. 5.My device is : - Camera:Busler scA640-70fm - NI pci 6221 - NI pci 8254r My programm is: Labview 8.5 Vision Builder AI 3.0.1 Vision assistant 8.0 Vision aquisition 8.2.2 What Can I manage my problem? I'm really need your help Help me please!!! Quote Link to comment
Antoine Chalons Posted January 17, 2009 Report Share Posted January 17, 2009 QUOTE (Poom-Thailand @ Jan 16 2009, 11:49 AM) I use the Vision Builder and convert to Labview file for use with control the servo motor. But I have some problem as shown below 1.When I finish the programm with Vision Builder I convert to Labview file ,in this state I don't found the problem 2.I cannot run Labview file because it has some problem about there are not found some of the command such as "IMAQ create" in the Block diagram and it is shown the "?" in the block ,then I don't sure that I'm install the programm right? 3.When I open Labview file again It was asked for "IMAQ image.ctl" and any of the file with type ".ctl,.ctt" I don't know where can I find? 4.When I use Labview to manage with the Image I input the command "IMAQ Build Coordsys" then the programm asked for many of the "IMAQ image.ctl" too. 5.My device is : - Camera:Busler scA640-70fm - NI pci 6221 - NI pci 8254r My programm is: Labview 8.5 Vision Builder AI 3.0.1 Vision assistant 8.0 Vision aquisition 8.2.2 What Can I manage my problem? I'm really need your help Help me please!!! Hi, The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create Hope this helps. Quote Link to comment
Antoine Chalons Posted January 17, 2009 Report Share Posted January 17, 2009 QUOTE (Poom-Thailand @ Jan 16 2009, 11:49 AM) I use the Vision Builder and convert to Labview file for use with control the servo motor. But I have some problem as shown below 1.When I finish the programm with Vision Builder I convert to Labview file ,in this state I don't found the problem 2.I cannot run Labview file because it has some problem about there are not found some of the command such as "IMAQ create" in the Block diagram and it is shown the "?" in the block ,then I don't sure that I'm install the programm right? 3.When I open Labview file again It was asked for "IMAQ image.ctl" and any of the file with type ".ctl,.ctt" I don't know where can I find? 4.When I use Labview to manage with the Image I input the command "IMAQ Build Coordsys" then the programm asked for many of the "IMAQ image.ctl" too. 5.My device is : - Camera:Busler scA640-70fm - NI pci 6221 - NI pci 8254r My programm is: Labview 8.5 Vision Builder AI 3.0.1 Vision assistant 8.0 Vision aquisition 8.2.2 What Can I manage my problem? I'm really need your help Help me please!!! Hi, The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create Hope this helps. Quote Link to comment
Poom-Thailand Posted January 18, 2009 Author Report Share Posted January 18, 2009 QUOTE (Antoine Châlons @ Jan 16 2009, 06:04 PM) Hi,The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create Hope this helps. I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program? Quote Link to comment
Poom-Thailand Posted January 18, 2009 Author Report Share Posted January 18, 2009 QUOTE (Antoine Châlons @ Jan 16 2009, 06:04 PM) Hi,The "IMAQ image.ctl" file is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\vision\Image Controls.llb\IMAQ image.ctl The "IMAQ create" function is located here : C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\Vision\Basics.llb\IMAQ Create Hope this helps. I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program? Quote Link to comment
Rolf Kalbermatter Posted January 19, 2009 Report Share Posted January 19, 2009 QUOTE (Poom-Thailand @ Jan 17 2009, 05:05 AM) I see in that folder but I cann't find "Image Controls.llb\IMAQ image.ctl" I don't sure is it cause mismatch about the version of the program? If you have installed the Vision Development Toolkit from the LabVIEW DVD go into Add/Remove Programs Control Panel and do a repair of your install. If you haven't yet done so then install that package. Rolf Kalbermatter Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.