Jump to content

FPGA Image Convolution error


Recommended Posts

Hi,

 

 

I am trying to use image convolution inside FPGA. My Image size is around 6kx2k. The convolution is applied properly until 2600 pixels in x resolution. After that, the values seem to miss previous row data. 

 

In Detail: As convolution is matrix operation, image data needs to be stored for the operation. But it seems there is an inadvertent error storing only 2600 pixels per row inside FPGA. And hence the filtered output is calculated assuming these pixels to be 0. 

 

I have tried with different image sizes, different convolution kernels, and also in different targets (cRIO 9030 and IC 3173). All results are same.

 

I have attached a screenshot of FPGA VI and an example image.

 

The example image shows an input image of 4000x2500 of same pixel value 16.The kernel is 3x3 of values 1 with divider=1. The RT image is processed using IMAQ convolute inside RT controller and has value 144 [(9*16)/1] for all pixels. But the FPGA processed image (zoomed in) has 144 until 2597 pixels and then 112 (7*16- showing 1 column of 2 rows missing) at 2598, 80 (5*16- showing 2 columns of 2 rows missing) at 2599 and 48 after that (missing 3 columns of 2 rows- current row is always present). This shows the data is missing from the previous rows after 2600 index.

 

Is there some mistake in the code or any workaround available?

Filter VI.PNG

FPGA Filter.png

Edited by prabhakaran
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Ricardo de Abreu
      Hi guys. This semester I'm starting a course system development for control and automation engineering, witch will be based on LabView. Therefore, my University doesn't have a NI hardware, even a MyRIO for us to test our VI and the teacher said that we should test our projects with our own Arduino...
      So, I have a little experience in Arduino and I know the basics for LabView. Now I'm in a point that I know that with Arduino I'll not take the best from LabView. I cannot even deploy a code to it.
      So, there is where my question comes in...
      I'm looking for a new board better then Arduino to use in the classes. I would buy a MyRIO card if I had the money but in Brazil this board is too expensive for me
       Witch one should I get that is closest to myRIO and less expensive than that? I would like to try de deployment of a VI and FPGA..... Is this possible?
      Thanks a lot for the help!
      Regards
    • By Maurice Rahme
      Hello, 
      I'm trying to implement an object tracking in LabVIEW. I've written a VI (attached) to detect and locate the centroid of elliptical shapes (because my circular subject can possibly be rotated and appear as an ellipse). However, the detection is not successful on every frame.
      For this reason, I would like to use the object detection method I've written as a ROI reference for an object tracker, whereby the object detector runs every 10-20 frames or so to make sure the tracker has not accumulated too much error. Any advice on how I can do this? Thanks! 
      Additionally, any criticism or advice on my object detection method would be appreciated. 
      Vision.vi
    • By GeT-Cameras
      Hello everyone,
      We have started with the development of our own embedded MIPI camera module for the Raspberry Pi with an industrial image sensor. Currently we are in the specification phase and we are interested in your preferences so we will develop a product that does fit your requirements. If you have some time, please consider filling in this 4-question questionnaire.
       
    • By grjgrj
      Hello. I need change some code for SbRIO-9626 with LabVIEW 2018. I have code from LabVIEW 2015. Right now I have only LabVIEW 2018. And I worked with it for SbRIO-9627.
      LabVIEW FPGA, LabVIEW Real-Time, NICRIO1800 driver istalled.
      And I install Xilinx ISE 11.5 Compilation Tool too. 
      When I start compilation FPGA VI I got error about problem with compilation too (see attachment picture).
      Could you tell me how I can solve this problem? 
      It is very important. 

    • By Shaun07
      Hello,
       
      Here, I have attached the VI in which I want to do auto exposure and set that exposure value.
      Basically this is program for laser beam analysis on live image. 
      Basically I want to set exposure time accordingly laser beam intensity. 
      If anyone previously worked on it then please help me with that. I am new to image processing. 
       
      Other image I attached, that's the part I want to implement with this program. 
      Help me out to solve this problem. 
       
      Thanks
       
      Thanks,
      Basic_Camera_Live_Beam_Information.vi

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.