Search the Community

Hello everyone, I have a development PC with labview community edition installed. On that PC an arduino uno is plugged with some sensors. I'm trying to get some data from a sensor attached to a raspberry pi. I saw a guy on the web that connected the pi to the PC using mobile hotspot on windows and loading the makerhub firmware and getting the IP that way. I managed to connect the pi to labVIEW and get it deploy any VI or control the GPIOs (i.e Untitled 2.vi). The thing is that I need to run a more broad VI from my main development PC (let's say Untitled 4.vi). Now I want not only to initialize a connection to the arduino uno, but also to the pi remotely. I've been trying to initialize the pi with the LINX (makerhub) open module and from the drop down menu choosing the remote I/O-TCP, but coudn't get it to work. Do I need to make any configuration to the raspberry pi from the properties meny on the Web-Server or the VI-Server tab? Or run a server from the raspberry itself? Which port to enter? I dont even know if what I'm trying to achieve is possible, can anyone help me out? Thank you.

Hi guys. This semester I'm starting a course system development for control and automation engineering, witch will be based on LabView. Therefore, my University doesn't have a NI hardware, even a MyRIO for us to test our VI and the teacher said that we should test our projects with our own Arduino... So, I have a little experience in Arduino and I know the basics for LabView. Now I'm in a point that I know that with Arduino I'll not take the best from LabView. I cannot even deploy a code to it. So, there is where my question comes in... I'm looking for a new board better then Arduino to use in the classes. I would buy a MyRIO card if I had the money but in Brazil this board is too expensive for me Witch one should I get that is closest to myRIO and less expensive than that? I would like to try de deployment of a VI and FPGA..... Is this possible? Thanks a lot for the help! Regards

Hello, I need a little help. I want to send from LabVIEW to Arduino via serial port the string for example "ABC" and so on. The problem is that when I send the string from LabVIEW .......the Arduino do nothing. Sometimes shows some kind of sign. When I send the string via Visual Studio it works perfectly. Is there someone who can help me. I attached picture of vi and Arduino code Thank you very much. Arduino code.txt

In my project i have 2 task (1).Read data of sensor (attached to arduino board) serially and display on LabVIEW. (2).Control output(just ON-OFF) pins of arduino using LabVIEW. So,for that i am using TAB in labview.created 2 TAB called Oscillospe and Input. If i first start Oscilloscope it work well. But when i come to Oscilloscope tab after using Input tab. It gives Time out error (VISA read) If i am executing in Highlight mode it works well tab--event.vi

I'm not sure if this is the right sub-forum, but is anyone playing with this? https://www.sparkfun.com/products/11225 I'd like to get a cheap copy of LabVIEW at home that isn't tied to work licenses. The application would be playing around with my kids.

Hi everyone, New on this site, new to Labview, new to RS232 and actually new to pretty much everything! Hope I'm not posting in the wrong section... I feel a bit out of place anyway to be posting among experts but well, for lack of a better place... So here's the context of my problems : I'm trying to set up a (crude) acquisition system based on an arduino and a couple of multiplexers / Thermocouple conditionners. My arduino is sending via its own USB-RS232 converter a string of all the values (approx. 20) as characters. I figured out I could use Labview to do a nice displaying and logging of these values. Now, I identified and downloaded VISA to communicate via RS232. OK so, in the MAX explorer, I have under port & peripherals the VISA test panel and if I try the viReadtofile under Basic I/O, it gives me a nice file with one set of values (one line). So it does communicate ! YAY!!! Onto the next part... I used a template from Labview, continuous datalogging and I just put the read to file VI but now when I press the RUN button, it gives me the two following errors. Error 1 occurred at Property Node (arg 1) in VISA Configure Serial Port (Instr).vi->Test_Read_VISA_1.vi Error -1073807346 occurred at VISA Read To File in Test_Read_VISA_1.vi Why is it already blocking my progress? And after that, I'm not sure I understand how can I process the output of the reading of the serial (basically, slicing the string of characters in it's values and displaying and logging them)? All the VI seem to directly process the serial readings to one thing without the opportunity for me to do anything to it... I'm attaching my VI even though it's pretty much only the read to file VI... I'm even ashamed to be that bad but I hope you guys will find enough faith in Labview to teach the basics to a newb like me! Thanks by advance! Marc Test_Read_VISA_1.vi

i have been seeing many discussions about "Arduino" and i have no knowledge about it. i am planing to go for a workshop soon. before the workshop i want to have little knowledge in this regard. Tried to search in labview forums that took me " NI LabVIEW Interface for Arduino Toolkit".page. I checked arduino's official website , still i need some understanding for effective usage.. what are the applications area where i can implement Arduino with Labview? please advise. thanks. note : i am reading "https://decibel.ni.com/content/groups/labview-interface-for-arduino" link now. is Arduino is having different standard hardware worldwide? pls help.

hey I am using Labview interface for arduino tool kit for interfacing LabVIEW and arduino to control the servo motor position but the problem is that the servo is moving to fast. Is there any way the speed of servo can be change Regards